spacer.png, 0 kB

spacer.png, 0 kB
 spacer.png, 0 kB
arrow Peltier - Thermoelectric Cooler Module Calculator
Thermoelectric (Peltier) Cooling Module Selector

Peltier - Thermoelectric Cooler Module Calculator

Note: This calculator requires JavaScript to be enabled.

Calculate the Thermoelectric (Peltier) cooling module that is best for your application

Click for instructions on how to use this Module Selector program.
Enter Cooling Requirements
Modules


DTmax of module:
°C
Need a starting point for DTmax?
70 °C is typical for an unpotted single-stage module
68 °C is typical for a potted module.
2
Heat Load (Q): watts
3
Hot-side Temperature: °C
4
Cold-side Temperature: °C
4
 Potted:
Information on potted or sealed
(terms are used interchangeably)
modules can be found on the page
Moisture Protection & Ruggedizing
 

   
Module Calculations

width=16 DT:    - Temperature difference, Thot - Tcold.
width=16
 DT/DTmax:    - Ratio of the module's operating temperature difference to the DTmax of the module.
width=16
 l/lmax for lowest power:    - Ratio of the module's suggested operating current to the Imax of the module.
width=16
 Q/Qmax for lowest power:    - Ratio of Q to Qmax of a module that's been optimized for minimum power consumption.
width=16
 Qmax for lowest power:  - Qmax of a module that's been optimized for minimum power consumption.
width=16
 Q/Qmax for smallest size:    - Ratio of Q to the minimum Qmax capable of meeting the cooling requirements.
width=16
 Qmax for smallest size:  - Minimum Qmax of a module that will meet the cooling requirement. This generally

   translates to a module that is as physically small as possible.
Suggested Modules

Suggested modules for lowest power consumption

Click on the module's name to link to it's specifications.
Product
Imax
(amps)
Vmax
(volts)
Qmax
(watts)
DTmax
(unpotted)
DTmax
(potted)
Width
(mm)
Length
(mm)
Height
(mm)






Suggested modules for smallest size

Click on the module's name to link to it's specifications.
Product
Imax
(amps)
Vmax
(volts)
Qmax
(watts)
DTmax
(unpotted)
DTmax
(potted)
Width
(mm)
Length
(mm)
Height
(mm)


Graphs

Please select a module and click the GRAPH button





Summary Report and Contact Information


If you require additional information not provided in this online module selector, please enter your contact information below and a TE Technology representative will contact you.

EMAIL PRIVACY POLICY:
We will use your email address only for the purpose of sending you the summary report from our design service. It will not be added to a mailing list or used for any other purpose. We will never share, sell, or rent individual personal information with anyone.
E-mail Address:  
Your Name:
Company Name:
Address:
Address2:
City, State/Province:
Zip/Postal Code:
Country:
Phone #:
Fax #:  
Comments:
Please provide as much detail as possible in the comments field to maximize the effectiveness of our response.



This report will include all of the information presented to you above. (Only E-mail Address is required for this.)


This will send a copy of the summary report to you and to a TE Technology engineer so that we can discuss your application further. (Required fields are indicated in bold.)
Disclaimer: The suggestions provided in the design analysis are only estimations based on the limited data submitted by you and do not take into consideration many other relevant factors. It is the responsibility of the customer to verify the design analysis and test the product in the desired application. TE Technology, Inc. has made no promises with regard to the design analysis. TE Technology, Inc. disclaims all warranties in connection with the design analysis, express or implied, as to any matter whatsoever, including without limitation description, quality, design, performance, specifications, condition, merchantability, and fitness for any particular purpose.
spacer.png, 0 kB
spacer.png, 0 kB
 spacer.png, 0 kB